Discovering Plumbing Basics is Essential for Bathtub Installation
Discovering Plumbing Basics is Essential for Bathtub Installation
Blog Article
What are your concepts on Tools You Need to Install a New Bathtub ?
Setting up a tub isn't specifically rocket science, however it does require solid plumbing, carpentry, and sometimes, tiling skills. Changing an old tub with a new one is additionally a reasonably difficult project. If the old tub is conveniently accessible, the task can move speedily; if you need to open a wall to eliminate the old bathtub and position the new bathtub, the task is a lot harder. In either case, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and also set in the brand-new one. Ensure you have qualified on your own for the task as well as fit trying it. Instead of working with a contractor to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube links.
This article will help you mount a new bath tub in your bathroom if you have already bought a brand-new tub as well as don't need to alter the setup of your previous water system pipelines.
Your devices as well as product list must consist of the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is separate the supply of water. After doing so, switch on the taps to drain pipes any water staying in the system. The process of removing the existing taps can be fairly problematic because of the limited access that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipelines have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing compound.
Before moving on to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washing machines remain in place in between the faucet and also the sink. Safeguard the tap in place with the manufacturer offered backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former kind should be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Tub
Using the two wooden boards under its feet, place the tub in the called for placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bathtub till the level checks out degree.
To install faucets, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression sign up with; then do the same for the various other faucet.
Activate the water as well as examine all joints and brand-new pipework for leakages and also tighten them if required. Fill up the tub and likewise check the overflow electrical outlet and the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait until the bathtub has been made use of at the very least once as this will settle it right into its last setting.
Planning for the Installation
Firstly, the sustaining frame supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets system to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its final placement.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to break a rigid seal, creating the water to pass through the wall in between the bath and also the tiling, leading to problems with moisture and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked paper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can fracture rather early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently readily available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that article about Installing A Bathtub when doing a search on the internet. Sharing is caring. Helping people is fun. I am grateful for your time. Visit again soon.
Go Company Report this page